Gasboy Atlas Start-up User Manual Page 160
- Page / 230
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 6-40 MDE-4334D Atlas™ Start-up and Service Manual · July 2013
Hydraulic/Mechanical Components Filters and Strainers
Service Tips
• Only hand-tighten the filter. Do not use a filter wrench to tighten.
• A light coating of oil on the gasket helps the seal to
seat properly and allows for easier
release at the time of removal.
• Use of a filter and strainer is required to ensure warranty
. Units that do not use filters will
commonly experience reduced life of hydraulic components. Use of only strainers for very
cold weather and diesel fuels is acceptable. However, filters must be used when warm
weather returns. The use of only a strainer will not ensure long life of hydraulic
components.
About Strainers
Strainers are installed between the manifold and filter to trap larger particles leaving the fine
filtering to be done by the filter element. The strainer helps to prolong filter life by preventing
premature filter clogging. Strainers can also help reduce the frequency of filter change,
resulting from fungus and slime conditions. Always reinstall or replace the strainer.
DEF Strainer
Filtration is required to protect the nozzles and valves. The earlier versions of the dispenser
relied completely on a filter tank system. The later versions of the dispenser have a strainer.
The 100-micron strainer and assembly is compatible with DEF. The strainer must be cleaned
after the first air purging and calibration to ensure good flow rates. Refer to “Purging Air from
System” on page 6-9.
Servicing Strainers
This section explains about servicing the strainers.
Cleaning/Replacing Standard and Hi-flow Filter Strainer
Figure 6-22 shows the standard and Hi-flow filter and stainer assembly.
Figure 6-22: Filter and Strainer Assembly
Manifold
Strainer with
cupped side up
Filter and Gasket
Service Tips
• Strainers commonly help reduce the frequency of filter change.
• Strainers can be cleaned with denatured alcohol. Replace the strainer if it is damaged or
pa
rtially clogged and not cleanable.
• Always check/clean the strainer, when
replacing a filter.
• Ensure that you note the orientation of the tabs when reinstalling the strainer
(see Figure 6-22).
- Start-up/Service Manual 1
- Approvals 2
- Trademarks 2
- Table of Contents 3
- Index Index-1 7
- 1 – Read This First 9
- Who Must Use This Manual 10
- Service Protocol 10
- Related Documents 11
- Abbreviations and Acronyms 12
- Common Terms Used 13
- DEF Special Considerations 14
- Troubleshooting DEF Freeze 15
- If DEF Freezes 16
- Model Information 18
- Atlas Model Number Table 21
- Options Overview 23
- In an Emergency 26
- Hazards and Actions 27
- Important Safety Information 28
- 3 – Start-up Procedures 29
- Start-up Checklists 30
- TURN OFF ENGINE 33
- Total Sale 34
- Configuring 9800 Series 35
- C06500-C06503) 36
- Configuration Steps 37
- ATC Setup 42
- Programming 8800 Series Units 43
- AT_PumpPCA_controller 44
- Manager Keypad Details 45
- Programming Errors 45
- Display Conventions 46
- Level 1 Programming 47
- Command Code 1: Program PPU 48
- Level 2 Programming 50
- 2 Press 10 51
- 3 Press Function # 51
- 4 Press Configuration # 51
- Level 3 Programming 54
- Function 55
- ATC Programming 56
- Displaying Pump Totals 57
- Error Codes and Descriptions 58
- Programming 8700 Series Units 59
- Range Arm 60
- Range Arm Locator 60
- Electronics Highlights 61
- Retail Parts by Name 62
- Retail Parts by Number 63
- Commercial Parts by Number 64
- About Service Procedures 68
- Preparing for Service 69
- Preventing ESD 69
- Hazardous Materials 70
- Manager’s 71
- Atlas 9800 PCAs 72
- U8 Programmed IC 73
- (Software) 73
- Atlas 9800 Parts 85
- Figure 5-23: LED Indicators 89
- Board (M06587A001) 94
- Jumpers JP4 and JP5 95
- Configurations 95
- Drive Board (M06587A001) 96
- AT_PumpPCA_interface 97
- AT_ATC_GR4 100
- ATC T-Meter Module PCA 102
- PCA Connections and Cables 102
- Power Supplies 106
- M04658A001 Cable 107
- M04659A001 Cable 107
- Figure 5-40: M04658A001 Cable 107
- Main Power Supply (T19868-G1) 108
- M04956A001 and Two Relays 109
- Q10131-03 Fuse 110
- About Displays 110
- Grade 2 B-Side 111
- Service Tips 112
- About Standard Pulsers 113
- Pulser Drive Assembly 114
- About Ultra-Hi Pulsers 115
- Introduction 121
- 2-stage Solenoid Valve 122
- Figure 6-2: CFT Meter 123
- General Service Procedures 124
- Before Beginning 126
- After Repairing 126
- Pipes and Hydraulic Plumbing 127
- Torque Specifications 128
- Purging Air from System 129
- Amount to Purge at Nozzle 130
- Using Nozzle to Purge Unit 131
- Purging Air in DEF Systems 132
- Measuring Flow Rate 133
- Measuring Pressure and Vacuum 134
- For Dispensers 135
- For Self-contained Pumps 136
- Reaching Required Flow Rate 138
- Measuring Vacuum for Pump 139
- About Vacuum Readings 139
- Measuring Dry Vacuum for Pump 139
- Acceptable Range Tables 141
- Meter Calibration 142
- IMPORTANT INFORMATION 143
- Locking Pin 144
- 0. PERCENT 145
- 0.0 PERCENT 145
- 0.00 PERCENT 145
- About Meters 146
- CFT/E85 Meters 147
- Repairing CFT/E85 Meters 148
- After Repairing Meters 149
- Replacing Piston Cups 151
- Seal Cap 153
- Screws (3) 153
- LC Meters 154
- Removing/Replacing LC Meters 155
- Coriolis Meter 155
- Electronics Module 156
- (M10006B501) 156
- Meter Programming Chip 156
- Filters and Strainers 157
- Servicing Filters 158
- Installing New Filters 159
- About Strainers 160
- DEF Strainer 160
- Servicing Strainers 160
- Hanging Hardware 161
- Hose Retrieval Mechanisms 162
- Replacing Hoses 162
- Flow Restrictors 163
- Breakaway Valves 164
- Resetting Breakaways 165
- Pumping Unit 170
- Draining GPU 171
- Removing PCV 174
- XU2A Pumping Unit for 9850K 178
- Draining Pump 179
- Pump Relief Valve 179
- Setting Relief Valve 180
- Adjusting Relief Valve 180
- Pump Lubrication 180
- Recommended Grease 180
- Sump for 9850K 181
- Pump Motor 182
- Belts and Pulleys 183
- Belt Adjustment 184
- Solenoid Valves 185
- Rebuilding or Replacing 186
- Troubleshooting 188
- Service Steps 188
- Meter Check Valve 189
- Shear Valves 190
- °F (-25°C). A T-52A 192
- Mechanical Computers 193
- DEF Nozzle 194
- 7 – Troubleshooting Tables 195
- Electronic Units) 196
- Sample Troubleshooting Form 197
- Priority Codes 198
- Table 1: 198
- Communications to Console 198
- Table 4: Error Codes 10-44 201
- 8 – Wiring and Configuration 205
- Preventive Maintenance 215
- Performing Inspections 216
- General Inspections 217
- Component Inspections 217
- Replacements and Adjustments 218
- Preserving Finish 219
- Preventive Maintenance Table 220
Related products and manuals for Hardware Gasboy Atlas Start-up
Hardware Gasboy 8800E User Manual
(1 pages)
(1 pages)
Hardware Gasboy 9800A User Manual
(2 pages)
(2 pages)
Hardware Gasboy 215A User Manual
(2 pages)
(2 pages)
Hardware Gasboy 9800A User Manual
(2 pages)
(2 pages)
Hardware Gasboy 9800A User Manual
(4 pages)
(4 pages)
Hardware Gasboy Lamp Kit User Manual
(2 pages)
(2 pages)
Hardware Gasboy 9120Q Pulser User Manual
(1 pages)
(1 pages)
Hardware Gasboy 9120Q Series User Manual
(26 pages)
(26 pages)
Hardware Gasboy 9820Q User Manual
(35 pages)
(35 pages)
Hardware Gasboy Electric Keytrol User Manual
(48 pages)
(48 pages)
Hardware Gasboy 215A User Manual
(31 pages)
(31 pages)
Hardware Gasboy 9700E User Manual
(82 pages)
(82 pages)
Hardware Gasboy 9100A User Manual
(68 pages)
(68 pages)
Hardware Gasboy 2150A User Manual
(31 pages)
(31 pages)
Hardware Gasboy 552A Series User Manual
(53 pages)
(53 pages)
Hardware Gasboy 9820A Series User Manual
(50 pages)
(50 pages)
Hardware Gasboy 9100Q Series User Manual
(51 pages)
(51 pages)
Hardware Gasboy 9800A User Manual
(1 pages)
(1 pages)
Hardware Gasboy 9800A Series User Manual
(125 pages)
(125 pages)
© 2020, manymanuals.com. All rights reserved. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals