Gasboy 1000 Series FMS Operation Manual User Manual Page 149
- Page / 241
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
05/29/03 19-1
Section 19
LITERS-PER-100KM OPTION
DESCRIPTION
The L/100KM (or LPH) option allows your Series 1000 system to calculate and maintain a
cumulative liters-per-100 kilometers or liters-per-hour* tally for a set number of your vehicles
(*NOTE: Liters-per-Hour is used when user equipment is monitored with an hour meter instead of
an odometer). The type of option, L/100KM or LPH, was determined when you ordered your
system. Also, the exact number of vehicles supported depends upon the limit specified when you
ordered your system. Vehicles in the system, but not in the vehicle file, are still permitted to fuel,
however, odometer/hours entries are not checked and L/100KM (or LPH) is not calculated.
Each vehicle in the file may be configured as to whether or not the system will calculate L/100KM
(or LPH) and execute a reasonable odometer/hours check on it. If this feature is disabled for a
vehicle record, the system will continue to update the total liters and odometer/hours entries, but
L100KM (or LPH) will not be calculated and a reasonable odometer/hours check will not be
executed.
L/100KM (or LPH) software computes fuel efficiency two ways: per transaction and averaged over
a period of time you determine (usually a month). To use the L/100KM (or LPH) option, you enter
information on your vehicles/equipment into vehicle records. These records are stored in a vehicle
file. The L/100KM (or LPH) option uses the vehicle data you enter plus calculated values to
provide total L/100KM (or LPH) information. The vehicle information for L/100KM is different than
that for LPH; both types are shown below.
The following information appears on vehicle file printouts for L/100KM:
● VEH 3- to 6-digit vehicle number
● B ODOM up to 6-digit beginning odometer reading
● E ODOM up to 6-digit ending odometer reading (last recorded)
● KLMS 6-digit kilometers driven
● LITERS up to 8-digits for total liters for period
● L/100 3 digits before and one after the decimal point indicating L/100KM value
● STAT a record status code indicating L/100KM comments (for more on status
flags, see the VF command)
The following information appears on vehicle file printouts for LPH:
● VEH 3- to 6-digit vehicle/equipment number
● B HOURS up to 6-digit beginning hours reading
● E HOURS up to 6-digit ending hours reading (last recorded)
● A HOURS up to 6-digit new, accumulated hours
● LITERS up to 8-digits for total liters for period
● LPH 3 digits before and one after the decimal point indicating LPH value
● STAT a record status code indicating LPH comments (for more on status flags,
see the VF command)
For both types, you can print out the vehicle file to view the vehicle number, beginning and ending
odometer/hours entries, the total number of kilometers/hours, the total number of liters, the liters
per 100 kilometers/liters-per-hour calculation (if enabled), and the record status.
- GASBOY INTERNATIONAL LLC 1
- Software Version 10 3
- CONTENTS 5
- OPTIONAL FEATURES 7
- FIGURES AND TABLES 11
- INTRODUCTION 13
- SYSTEM FEATURES 14
- HOW TO USE THIS BOOK 18
- Section 2 19
- Section 3 21
- COMMUNICATION TERMINATIONS 22
- INITIATING COMMUNICATION 23
- LS - LOAD SIGN-ON PASSWORD 24
- LOST OR FORGOTTEN PASSWORD 25
- Section 4 27
- HE - HELP COMMAND 30
- Section 5 33
- ● Number of lines per page 35
- ● Card expiration date 35
- ● Auto PIN lockout 35
- ● Auto site shut down 35
- 05/29/03 5-7 39
- LD - LOAD DATE AND TIME 41
- PD - PRINT DATE AND TIME 42
- SD - LOAD SITE DOWN TIME 43
- VA - VALIDATE ALL CARDS 50
- IA - INVALIDATE ALL CARDS 53
- CC - CHECK CARD VALIDATION 56
- PV - PRINT VALID CARD LIST 57
- PI - PRINT INVALID CARD LIST 58
- TANK INVENTORY COMMANDS 61
- LI - LOAD TANK INVENTORY 62
- AI - ADD TO TANK INVENTORY 63
- TI - PRINT TANK INVENTORY 65
- PUMP COMMANDS 67
- LP - LOAD PUMP DATA 68
- PP - PRINT PUMP DATA 71
- EP - ENABLE A PUMP 72
- DP - DISABLE A PUMP 73
- AP - ACTIVATE A PUMP 75
- IP - INACTIVATE A PUMP 76
- ZP - ZERO PUMP TOTALIZERS 77
- TRANSACTION COMMANDS 79
- RT - RESET TRANSACTION FILE 88
- LN - LOAD TRANSACTION NUMBER 90
- TRANSACTION MESSAGES 92
- Section 10 95
- LL - LOAD FUEL LIMITATIONS 98
- PL - PRINT FUEL LIMITATIONS 99
- Section 11 101
- ● PP to obtain pump totals 102
- Section 12 105
- ENTRIES 107
- ● Hours-Per-Liter Option 108
- DUAL LOCKOUT OPTION 111
- FUEL ALLOCATION OPTION 113
- FUEL ALLOCATION EXAMPLES 114
- AO - ALLOCATION OFFSET 115
- LA - LOAD ALLOCATION 116
- AA - ADD TO ALLOCATION 118
- CA - CHECK ALLOCATION 122
- PA - PRINT ALLOCATION TABLE 125
- Section 15 129
- FUEL DELIVERIES 130
- DIPSTICK READINGS 131
- GATE CONTROLLER OPTION 133
- LG - LOAD GATE TIMEOUT 134
- PG - PRINT GATE TIMEOUT 135
- AG - ACTIVATE GATE 136
- CHANGES IN STANDARD COMMANDS 138
- LOADABLE BASE PUMP OPTION 143
- MANUAL KEYPAD ENTRY OPTION 147
- LITERS-PER-100KM OPTION 149
- CV - CLEAR VEHICLE FILE 151
- GASBOY Series 1000 154
- 19-6 05/29/03 154
- Example for LPH: 154
- RV - REMOVE A VEHICLE RECORD 155
- LO - LOAD ODOMETER/HOURS 156
- IV - INITIALIZE VEHICLE FILE 157
- VF - PRINT VEHICLE FILE 158
- CR - CHECK VEHICLE RECORD 162
- TRANSACTION PROCESSING 165
- TRANSACTION HEADINGS 168
- 19-22 05/29/03 170
- Example: PS Command: 170
- L/100 KM (OR LPH) MESSAGES 171
- Section 20 173
- PUMP SWITCH TIMER OPTION 177
- REASONABLE ODOMETER/HOURS 181
- CHECK OPTION 181
- LV - LOAD A VEHICLE RECORD 184
- 05/29/03 22-11 191
- Example: PS Command 191
- ODOMETER/HOURS CHECK 192
- RECEIPT PRINTER OPTION 193
- FUELING PROCEDURE 194
- GR - GET RECEIPT COMMAND 195
- RECEIPT PRINTER MESSAGES 200
- SUPERVISOR CARD OPTION 201
- TANK MONITOR INTERFACE 205
- ● ENQ (CTRL E) termination 207
- ● Timeout termination 207
- TANK MONITOR ERROR MESSAGES 209
- PREVENTIVE MAINTENANCE 211
- Section 27 213
- SWITCHES AND SETTINGS 214
- CHANGING THE PAPER 216
- CHANGING THE RIBBON 217
- ADJUSTING CUTTER BLADES 219
- Appendix A 221
- AUTO PIN LOCKOUT 223
- LK - LOAD PIN KEY 223
- LC - PRINT LAST CARD(S) READ 223
- CARD VALIDATION COMMANDS 224
- PT - PRINT TRANSACTIONS 224
- PH, PC COMMANDS 225
- FUELING RESTRICTION COMMANDS 225
- Appendix B 229
- OKIDATA 184 SETUP 231
- 05/29/03 Index-1 233
- Index-2 05/29/03 234
- Index 235
- 05/29/03 Index-3 235
- Index-4 05/29/03 236
- 05/29/03 Index-5 237
- Index-6 05/29/03 238
- 05/29/03 Index-7 239
- WARRANTY 241
Related products and manuals for Hardware Gasboy 1000 Series FMS Operation Manual
Hardware Gasboy MCE300 User Manual
(71 pages)
(71 pages)
Hardware Gasboy 4-Hose PCU User Manual
(2 pages)
(2 pages)
Hardware Gasboy CFN Series User Manual
(42 pages)
(42 pages)
Hardware Gasboy KE200 User Manual
(119 pages)
(119 pages)
© 2020, manymanuals.com. All rights reserved. | 2.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals