Gasboy 70 Series User Manual download pdf (Page 3)

MDE-4423B Series 70 and 1800 Consumer Elect Pumps Installation/Operation/Parts

●

July 2005 Safety-1

IMPORTANT WARNINGS AND SAFEGUARDS

Gasoline and petroleum products are flammable. To avoid injury or death to persons or damage to equipment or property, follow these

listed warnings and other warnings and precautions outlined in this manual when installing, using, or working around this equipment.

Check with Gasboy Technical Services for compatibility of liquids with pump materials.

TURN OFF AND LOCK OUT ALL POWER TO PUMP BEFORE PERFORMING SERVICE, MAINTENANCE OR IN THE EVENT

OF A FUEL SPILL.

All products must be installed by a qualified

installer and used in conformance with all

building, fire, and environmental codes and

other safety requirements applicable to its

installation and use, including, but not

limited to, NFPA 30, NFPA 30A, NFPA

395 & NFPA 70. A qualified installer is

familiar with fuel systems installations under

the above stated building, fire, and

environmental codes and other safety

requirements for the particular type of

installation.

This product is only part of a fuel dispensing

system and additional equipment and

accessories, such as, but not limited to,

breakaway connectors, shear valves,

pressure regulators, flow limiters, and other

safety devices may be necessary to meet the

applicable codes.

For maximum safety, we recommend that all

employees be trained as to the location and

procedure for turning off power to the entire

system. Instructions regarding proper

operation of the equipment along with the

appropriate safety warnings should be

posted in plain view at the fuel island.

Before performing service or maintenance

(including changing of fuel filters or

strainers) or in the event of a fuel spill, turn

off and lock out all power to the system. In

battery-powered pumps, disconnect power

source. In submersible pump applications,

turn off and lock out power at the master

panel and close any impact valves to the

submersible pump and any other dispensers

which use that submersible pump. AC

power can feed back into a shut-off

dispenser when dispensers share a common

submersible pump or starter relay. Also

block islands so no vehicles can pull up to

the dispenser when performing maintenance

on the dispenser.

DO NOT use Teflon tape for any pipe

threads in the product.

DO NOT use consumer pumps for pumping

fuel or additives into aircraft.

DO NOT use commercial pumps for direct

fueling of aircraft without filters and

separators necessary to ensure product

purity.

DO NOT use where sanitary design is

required (for food products for human

consumption) or with water-based liquids.

DO NOT smoke near the pump or when

using the pump.

DO NOT use near open flame or electrical

equipment which may ignite fumes.

DO NOT permit the dispensing of gasoline

or other petroleum products into a vehicle

with its motor running.

DO NOT permit the dispensing of gasoline

or other petroleum products into

unapproved containers or into approved

containers in or on vehicles including

trucks. All containers must be filled on the

ground to prevent static discharge. Always

use Approved and Listed hoses and nozzles

with electric pumps and dispensers.

DO NOT block open the nozzle in any

manner. Nozzles shall conform to UL and

NFPA code requirements for attended or

unattended service.

DO ensure that the pump is equipped with

proper filters based on the product being

dispensed and its intended use.

DO wear safety goggles and protective

clothes when dispensing any liquid which

may be potentially harmful or hazardous.

DO keep all parts of body and loose

clothing clear of belts, pulleys, and other

exposed moving parts at all times.

DO require washing and changing of clothes

if fuel is spilled on a person or his/her

clothing. Keep away from open flames,

sparks, or people smoking.

DO provide a receptacle for catching

product from pump/meter when servicing.

DO clean up product spills on the driveway.

Turn off and lock out all power prior to

cleanup.

DO ensure pump is properly grounded.

DO ensure hose is compatible with fluid

being dispensed.

DO inspect hose, nozzle, and pump on a

regular basis for wear, damage, or other

conditions which may create a safety or

environmental hazard.

DO make sure all pipe threads are properly

cut and the inside reamed to remove burrs.

Use UL classified gasoline-resisting

compound on all joints of gasoline handling

piping. Sealing compound must also be

resistant to Gasohol (Ethanol and

Methanol). Use gasoline-resistant pipe

compound on male threads only; pipe

compound used on female threads can be

squeezed into the supply line where it can

enter the product stream and become

lodged in the pump or meter.

DO ensure that junction box covers are in

place and properly tightened. Mating

surfaces between the box and cover must be

free of dirt, nicks, and scratches. Properly

plug all unused entries into the junction box.

1 2 3 4 ... 53

Comments to this Manuals

No comments

Gasboy 70 Series User Manual Page 3

Comments to this Manuals

Related products and manuals for Hardware Gasboy 70 Series